• November 23, 2024, 12:28:03 PM

Login with username, password and session length

NOTE: This forum is for respectful dialog and it's content is meant to be kept on this site - so please be respectful and please do not copy content to other sites.

Author Topic: Castle lock 3 light not working  (Read 18987 times)

Offline Fuse

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 17
  • Karma: +0/-0
    • View Profile
Castle lock 3 light not working
« on: June 10, 2015, 11:29:03 PM »
I thought because I had the game on normal that you only lock 2 balls then multi ball starts and if you played it on the hard setting you would have to lock 3 balls first. So I just thought that the castle lock 3 would never light. Well I watched it in attract mode and thought it was funny that it didn't light. Went into single lamp test and selected it and it will not light. Lifted the Playfield and if I wiggle or hold the connector it will light. However I cannot keep it lit once I take my hand off the connector. Wiggled the wires below the connector and it wouldn't light.  So I'm assuming it's a cold solder on  the other side of the Playfield.  I really hope this isn't the case since all the connectors are hot glued and plenty of them.  I haven't done it but I think another connector could be swapped and go through the lamp test to see if the castle lock 3 lamp test would light another insert. That would prove the connector is good. Is this test ok to try Lloyd. All connectors have the same ground pinout?

Offline Lloyd Olson

  • LTG : )
  • Global Moderator
  • Three Star Member
  • *****
  • Posts: 385
  • Karma: +18/-7
    • View Profile
Re: Castle lock 3 light not working
« Reply #1 on: June 11, 2015, 12:34:17 AM »
Yes please try another connector.

If that doesn't do it, please open a ticket on the help desk.

Thank you.
LTG : )

Offline Fuse

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 17
  • Karma: +0/-0
    • View Profile
Re: Castle lock 3 light not working
« Reply #2 on: June 11, 2015, 08:29:42 AM »
Ok. I'm gone for the day but may get at it tonight.

Offline Fuse

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 17
  • Karma: +0/-0
    • View Profile
Re: Castle lock 3 light not working
« Reply #3 on: June 11, 2015, 11:57:03 PM »
Ok. Definite pcb problem. If I barely flex the pcb by that connector the light will come on.  If anyone from pps or cgc wants to see a video of this I have one.  I will create a cgc ticket.

Offline PPS

  • Administrator
  • Five Star Member
  • *****
  • Posts: 1185
  • Karma: +60/-37
  • PPS Owner
    • View Profile
Re: Castle lock 3 light not working
« Reply #4 on: June 12, 2015, 02:31:39 AM »
sounds like connector/pcb, so cgc will handle this.


Offline Lloyd Olson

  • LTG : )
  • Global Moderator
  • Three Star Member
  • *****
  • Posts: 385
  • Karma: +18/-7
    • View Profile
Re: Castle lock 3 light not working
« Reply #5 on: June 12, 2015, 02:11:28 PM »
Ron will be contacting you shortly.

Thank you,
LTG : )

Offline Fuse

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 17
  • Karma: +0/-0
    • View Profile
Re: Castle lock 3 light not working
« Reply #6 on: June 12, 2015, 04:47:51 PM »
Ok. Thanks Lloyd!

Offline Fuse

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 17
  • Karma: +0/-0
    • View Profile
Re: Castle lock 3 light not working
« Reply #7 on: June 16, 2015, 09:54:14 PM »
No response from cgc in 4 days.

Offline Lloyd Olson

  • LTG : )
  • Global Moderator
  • Three Star Member
  • *****
  • Posts: 385
  • Karma: +18/-7
    • View Profile
Re: Castle lock 3 light not working
« Reply #8 on: June 16, 2015, 11:13:59 PM »
I'm sorry for what ever went wrong.

I'll be speaking with Ron at CGC in 12 1/2 hours or so and bring this up.
Lloyd