• November 23, 2024, 07:37:41 AM

Login with username, password and session length

NOTE: This forum is for respectful dialog and it's content is meant to be kept on this site - so please be respectful and please do not copy content to other sites.

Author Topic: Difficulty shooting Merlin Magic  (Read 28466 times)

Offline Turbo27

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 15
  • Karma: +0/-0
    • View Profile
Difficulty shooting Merlin Magic
« on: January 27, 2017, 02:35:21 AM »
Finding it increasingly difficult to hold a ball into Merlin Magic.

A sweet shot particularly from the left flipper fires straight through. About the only way I seem to hold a ball in there is from a miss-hit after it hits something else slowing the momentum of the ball.

Anyone else ??? Any modifications suggested???

Thank you

Offline gliebig

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 46
  • Karma: +0/-0
    • View Profile
Re: Difficulty shooting Merlin Magic
« Reply #1 on: January 27, 2017, 08:49:16 AM »
I don't know.  Any place to stick some foam back there?
Mine stays in the hole 95% of the shots.

Offline schonb25

  • PPS Forum Member
  • Two Star Member
  • *
  • Posts: 74
  • Karma: +5/-11
    • View Profile
Re: Difficulty shooting Merlin Magic
« Reply #2 on: January 29, 2017, 10:08:30 PM »
Same on the original. Some drop dead foam on the back of the metal will help a lot.

Offline Turbo27

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 15
  • Karma: +0/-0
    • View Profile
Re: Difficulty shooting Merlin Magic
« Reply #3 on: January 30, 2017, 12:48:25 AM »
Thanks for the replies.
Tried the foam and even re-tensioned the spring on the gate entrance.

No improvement

Almost as frustrating as mode start on Indy!

Offline whoeverwhocares

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 43
  • Karma: +2/-1
    • View Profile
Re: Difficulty shooting Merlin Magic
« Reply #4 on: February 13, 2017, 10:20:44 PM »
There must be something that isn't set right or is off a bit near the hole. Based on what people say on here I expected it to be a lot worse when I got mine, but it stays in 99% of the time. I should add that I have the Mantis protector and the front comes up a hair higher than the playfield, which may help deaden the ball, but it doesn't impede it's path in any way.
« Last Edit: February 15, 2017, 09:23:00 AM by whoeverwhocares »

Offline hocuslocus

  • PPS Forum Member
  • Two Star Member
  • *
  • Posts: 53
  • Karma: +2/-0
    • View Profile
Re: Difficulty shooting Merlin Magic
« Reply #5 on: March 13, 2017, 04:41:17 PM »
Dead foam. just make sure you position it far enough up the pole so that it doesn't interfere with the kickout.

You are not allowed to view links. Register or Login

Offline Hooked

  • PPS Forum Member
  • Two Star Member
  • *
  • Posts: 69
  • Karma: +0/-1
    • View Profile
Re: Difficulty shooting Merlin Magic
« Reply #6 on: March 29, 2017, 10:17:20 PM »
I too have this issue....shot tends to bounce out to the pops. I plan on dropping the seat it sits in using washers....worked great on avengers. Foam dis not fix my pop.out issue on mmr
Hookedonpinball.com

Offline Turbo27

  • PPS Forum Member
  • One Star Member
  • *
  • Posts: 15
  • Karma: +0/-0
    • View Profile
Re: Difficulty shooting Merlin Magic
« Reply #7 on: May 12, 2018, 05:22:32 PM »
Update on this problem.

Foam didn't work, so I removed the entire VUK Merlin assembly. 4 screws from the underside. I do love how all the electrical components are plugs or sockets for easy removed !! Nice

There is a curved metal scoop, half moon piece that directs the ball into the seat.

I'm guessing that I made too many direct hits with the ball into the metal scoop, cause it had bent.

To fix, I obviously bent it back, but in a clockwise direction. Wish I had taken a photo to better explain.

Now, Merlin is keeping the ball seated, 9 times out of 10. Big improvement.