Messages

1

MMR Support [MMR Members Only] / Re: Time and date resetting- new code

« on: August 11, 2016, 11:34:57 AM »

I have had 3 days in a row now.

2

MMR Support [MMR Members Only] / Re: Troll carriage broken weld

« on: June 14, 2016, 03:39:32 PM »

Troll has been fixed. Thanks CGC for getting me the part.

3

MMR Support [MMR Members Only] / Re: Troll carriage broken weld

« on: June 11, 2016, 04:33:32 PM »

Got an invoice today from CGC for the broken carriage assembly. I must return the broken part within 14 days, however according to the UPS tracking number they haven't shipped the part yet. I guess I should be glad that I have a UPS tracking number. 

4

MMR Support [MMR Members Only] / Re: Troll carriage broken weld

« on: June 09, 2016, 09:12:53 PM »

17 days and still "Being Processed   since 16 days 20 hours". Sure would like to have both trolls working.

5

MMR Support [MMR Members Only] / Re: Troll carriage broken weld

« on: May 25, 2016, 11:38:05 AM »

CGC responded to my ticket that they were sending a replacement.

6

MMR Support [MMR Members Only] / Re: Where to pull 12V?

« on: May 24, 2016, 10:08:33 PM »

did you ever find a good source for the 12V?

7

MMR Support [MMR Members Only] / Re: Troll carriage broken weld

« on: May 24, 2016, 10:05:49 PM »

As Lloyd said right above the locknut. On the left troll you can see the break just below the trolls chin.


 

8

MMR Support [MMR Members Only] / Re: Troll carriage broken weld

« on: May 24, 2016, 10:38:28 AM »

Picture was good enough for Chicago Gaming, they have already responded to the ticket.

9

MMR Support [MMR Members Only] / Troll carriage broken weld

« on: May 24, 2016, 01:03:40 AM »

Just unboxed MMr Le 839 and discovered during the first game that the troll carriage had a broken weld where the switch attaches. The troll was not centered when raised and moved a little when hit by a ball. I have disabled the left troll in the adjustment menu. I have attached a picture of the broken weld that causes the issue.


I have submitted support ticket #670 with Chicago Gaming.
 

10

MMR Support [MMR Members Only] / Re: MMR diffuser installed

« on: March 30, 2016, 04:00:19 PM »

Thanks for posting the photos. Just need to see if newly built games come with the diffusers already installed.

11

MMR Support [MMR Members Only] / Re: Slam tilt switch is stuck closed

« on: February 21, 2016, 02:03:58 PM »

According to the schematics on page 3-13 both slam switches are wired in parallel and connected to SW21. We need to figure out which slam switch is causing the problem.


There is a connector for the coin door J4. If you pull this connector instead of J3 on the controller board does the slam switch still register as closed?


If yes its either the Cabinet slam or the cabinet wiring.


If no, then the coin door switch is the culprit.


Loosen the screws holding the switch to either the door or the cabinet and wiggle the entire assembly to see if there is a short in the assembly and the Green with black stripe wire. This can be done while in the switch test to see if you get any indication that the switch is working. 




   

12

MMR Support [MMR Members Only] / Re: Slam tilt switch is stuck closed

« on: February 19, 2016, 05:36:04 PM »

[size=78%]There should be another switch inside the cabinet by the plumb bob tilt or on the cabinet floor by the coin box. Sorry I don't have an MMR yet to get an exact location for you. [/size]

13

MMR Support [MMR Members Only] / Re: Slam tilt switch is stuck closed

« on: February 19, 2016, 05:10:47 PM »

The missing wire is normal. According to the schematics its used for the coin lockout and is not used in MMR. Could you post a picture of the slam tilt switch in the coin door?