1
MMR Support [MMR Members Only] / Re: Coin acceptor for MMR
« on: July 26, 2016, 10:36:17 PM »
I did same thing , Loyd had advised me previously and both mechs fit fine without cutting anything !
- November 23, 2024, 10:15:22 AM
NOTE: This forum is for respectful dialog and it's content is meant to be kept on this site - so please be respectful and please do not copy content to other sites.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
MMR Support [MMR Members Only] / Re: Diffuser Help...
« on: July 14, 2016, 01:03:35 PM »
For those of you that have installed the diffuser , do you see a difference ?
I am thinking of ordering but don't want to dissemble the game if effect is minimal or not at all ,
Mine is an early production, dated April 15, 2015
I am thinking of ordering but don't want to dissemble the game if effect is minimal or not at all ,
Mine is an early production, dated April 15, 2015
3
MMR Support [MMR Members Only] / Re: Slingshot Damage
« on: July 18, 2015, 03:38:40 AM »
Just installed my kit as well . Old plunger measuredv2" even , new plunger measures 2 1/4 " .
It results in a nice clear 1/8 " to 3/16" clearance on the kicker playfield hole . I fortunately did not have visible damage but did the upgrade to be sure .
It results in a nice clear 1/8 " to 3/16" clearance on the kicker playfield hole . I fortunately did not have visible damage but did the upgrade to be sure .
4
MMR Support [MMR Members Only] / Re: Slingshot Damage
« on: July 17, 2015, 01:59:21 AM »
Just got my slingshot plunger replacements in the mail from CGC today . 2 plungers with bellcranks and detailed installation instructions .reuse same kicker arms .
5
MMR Support [MMR Members Only] / Re: Left kickup from the moat
« on: June 04, 2015, 10:35:29 PM »
Great news Sandbagger , now go enjoy your game !!!!
6
MMR Support [MMR Members Only] / Re: Left kickup from the moat
« on: June 02, 2015, 12:23:58 AM »
After installing a Mantis protector on the kick out area I found that I had the same problem , ball would rarely come out to the playfield . After further inspection I found that I had to realign the kicker assembly by loosening the 3 mounting screws and rotating it slightly clockwise . If you inspect assembly from the top you will see that as the ball is kicked up it is hitting the playfield metal guide ramp at the outlet area and dropping it back down . Not a hard fix but must be perfectly aligned . Hope this helps . Paul
7
MMR Support [MMR Members Only] / Re: Catapult launch is to strong
« on: May 31, 2015, 11:53:35 PM »
Apparently the original ramp must have been misformed or bent . I moved and then tightened the original ramp minutely left and then right at castle mount maybe 50 times trying to fine tune it . It was never right and was smashing the red strobe light or the back side of the castle 30 + percent of the time . CGC sent out new ramp and problem was immediately solved . Even before I fine tuned it the difference was obvious . Now the ball flow from the catapult into and around the rampant is smooth as silk . I hope this clarifys the issue .
Thanks, Paul
MMR # 201
Thanks, Paul
MMR # 201
8
MMR Support [MMR Members Only] / Re: Coin mechs ? What is needed .
« on: May 31, 2015, 02:31:46 PM »
I just finished installing coin mechs . No issues whatsoever , moved center wire tie that was attached to the door , set wires into the recessed area and mounted the mechs . Works great and the machine recognizes the coins ! Ps. I did not have to reroute anything nor disconnect anything . Just moved the one wire tie from the door mount behind the new mechs and left it loose . Mechs now keep it in the proper area with no compression on the wires whatsoever .
9
MMR Support [MMR Members Only] / Re: Catapult launch is to strong
« on: May 31, 2015, 02:28:17 PM »
Chicago Gaming sent out a new ramp to cure my catapult issue ,
New ramp solved the problem and catapult now works perfectly .
Many Thank loyd and CGM
Paul
New ramp solved the problem and catapult now works perfectly .
Many Thank loyd and CGM
Paul
10
MMR Support [MMR Members Only] / Re: MMR Software Updates - Coming Soon
« on: May 15, 2015, 02:41:30 AM »
On the update , the catapult coil is already adjustable , but it goes -default to +1 to +2.
Default coil strength is already to high and I would like to also see a -1 to -2 . I have adjusted ramp many times and even in its best location , ball still smashes into the upper red plastic light and then comes backwards down the left side up ramp .
It really pains me to see my new game get beat up during regular game play . I had previously reported this on another thread .
Anyone else out there experiencing similar catapult problems ?
Paul , Miami , Fl # 201
Default coil strength is already to high and I would like to also see a -1 to -2 . I have adjusted ramp many times and even in its best location , ball still smashes into the upper red plastic light and then comes backwards down the left side up ramp .
It really pains me to see my new game get beat up during regular game play . I had previously reported this on another thread .
Anyone else out there experiencing similar catapult problems ?
Paul , Miami , Fl # 201
11
MMR Support [MMR Members Only] / Catapult launch is to strong
« on: May 11, 2015, 01:22:37 AM »
I have catapult launch set at default which appears to be the minimum power . When my catapult fires the ball goes quickly up the ramp . then hits the red attract light right at then end of the metal catapult ramp which then deflects the ball-straight backwards down through the left ramp entrance .
Isn't the catapult supposed to launch the ball so it goes around the ramp and returns through the wires to the left flipper ? Anyone else having this issue ? Any fixes ?
Paul - # 201
Isn't the catapult supposed to launch the ball so it goes around the ramp and returns through the wires to the left flipper ? Anyone else having this issue ? Any fixes ?
Paul - # 201
12
MMR Support [MMR Members Only] / Re: Game just went dead
« on: May 09, 2015, 12:10:35 AM »
New Power Supply installed and game is playing perfectectly ! Many thanks to Loyd -Sean - Ron and CGM .
I couldn't be more pleased with the excellent timely response to this issue
Job well done ,
Paul
I couldn't be more pleased with the excellent timely response to this issue
Job well done ,
Paul
13
MMR Support [MMR Members Only] / Re: Game just went dead
« on: May 07, 2015, 12:47:26 AM »
Support from both Loyd and CGM ( Sean and Dave ) has been exceptional ! Looks like I lost the 12 volt side of the power . We walked through the testing over the phone today . . They are sending out a new power supply for me to install immediately . I am very pleasantly surprised at the quick response .
Many Thanks
Many Thanks
14
MMR Support [MMR Members Only] / Re: Game just went dead
« on: May 06, 2015, 08:53:23 AM »
Loyd ,
I will check all connectors when I return home . I did send you an email and also started a ticket .
Will let you know what I find regarding all connections ,
Thanks., Paul
I will check all connectors when I return home . I did send you an email and also started a ticket .
Will let you know what I find regarding all connections ,
Thanks., Paul
15
MMR Support [MMR Members Only] / Game just went dead
« on: May 06, 2015, 12:38:08 AM »
Loyd ,
After about 20 perfect fully functioning plays , my game just went completely dark during play #21. I tested voltage in and all is good 110 . The green lights at the bottom right box next to coin door are lit . The extra power plug there reads 110 . The 3 banks of green lights next to fuse blocks on underside of playfield are lit . The board behind the backglass is dark . All playfield lights , mechs , and backglass dark and non functioning as well . I don't want to research anything further without your expert advice . I don't know of a reset or bad board or ?
Please get back to me as I want to get playing again soon .
Thanks , Paul
Miami, Fl .
MMRLRE # 201
After about 20 perfect fully functioning plays , my game just went completely dark during play #21. I tested voltage in and all is good 110 . The green lights at the bottom right box next to coin door are lit . The extra power plug there reads 110 . The 3 banks of green lights next to fuse blocks on underside of playfield are lit . The board behind the backglass is dark . All playfield lights , mechs , and backglass dark and non functioning as well . I don't want to research anything further without your expert advice . I don't know of a reset or bad board or ?
Please get back to me as I want to get playing again soon .
Thanks , Paul
Miami, Fl .
MMRLRE # 201
Pages: [1] 2